• We have updated the site to the latest version. You will be required to log in to make sure your account is active. There are quite a few new functions so it will take a little time to get use to it. Please post if you see or have any issues.

New to the forum and looking to upgrade my 99 xc 700 suspension Front and rear.

mxfan127

New Member
Messages
3
Age
39
Location
Se WI
Country
USA
Years Snowmobiling
20+
Snowmobile
Polaris XC 700/XC 500
I'm looking for a set of front shocks and springs and a rear sled from a newer platform my sled has low miles and still runs like new just getting beat up on the trails any advise is also welcome..


Sent from my iPhone using Tapatalk
 
I'm looking for a set of front shocks and springs and a rear sled from a newer platform my sled has low miles and still runs like new just getting beat up on the trails any advise is also welcome..


Sent from my iPhone using Tapatalk

Rear:

If your okay with sacrificing 5 mph top speed, an m10 is still a good swap. Plus the information you need is everywhere.

Stay away from the mid to late 2000s Polaris m10s with the tubular arms. Nothing wrong with tubes per se, but these skids are not built as well and are prone to cracking.

M10 needs to be setup correctly. When it is, you get a great ride.

Or: 2002 and up Polaris "edge" skids, fusion skids, Dragon skids, even new indy skids. They are conceptually and geometrically the same. Just detail changes and trim changes thru the years.

******No matter what you choose, the shocks need to be fresh and valved correctly. Correctly as in, at least to OEM spec******

In all honesty you could swap any skid. Even an r motion. But with the edge style and m10 you are scaffolding off over 10 years of swap knowledge on the web. So it's just easier.

Front shocks:

The front of your machine thankfully has a modern level of travel and decent geometry. So you just need shocks, or your shocks serviced.

Check out this guy below...he builds and sells fox aluminum body and steel body shocks. Internal floating piston or reservoir. Great prices and he knows all the oem valve codes, shock length and bushing sizes for the older stuff.

http://snorunner.byethost9.com

Hygear and Monster performance are good too. Though I think they cator to newer sleds more.

With the front shocks, request the big heavy duty fox bottom out bumpers. They make a big difference. You can have a more compliant ride with good bottom resistance. It's like dual rate springs. They even make dual rates better too.

Another thing that helps is getting your bars up to a more modern level and raising the seat. Grafting a fusion seat or some other higher seat is a big benefit.

I built a 2000 Indy 500xc sp with a lifted fusion seat, m10, bar risers and good front shocks. I had 3 Great seasons on that sled and liked it. So much so that my 2011 ski doo xp was a little disappointing until I got the shocks upgraded. Especially the front.

If you have any questions, just ask.
 
Rear:

If your okay with sacrificing 5 mph top speed, an m10 is still a good swap. Plus the information you need is everywhere.

Stay away from the mid to late 2000s Polaris m10s with the tubular arms. Nothing wrong with tubes per se, but these skids are not built as well and are prone to cracking.

M10 needs to be setup correctly. When it is, you get a great ride.

Or: 2002 and up Polaris "edge" skids, fusion skids, Dragon skids, even new indy skids. They are conceptually and geometrically the same. Just detail changes and trim changes thru the years.

******No matter what you choose, the shocks need to be fresh and valved correctly. Correctly as in, at least to OEM spec******

In all honesty you could swap any skid. Even an r motion. But with the edge style and m10 you are scaffolding off over 10 years of swap knowledge on the web. So it's just easier.

Front shocks:

The front of your machine thankfully has a modern level of travel and decent geometry. So you just need shocks, or your shocks serviced.

Check out this guy below...he builds and sells fox aluminum body and steel body shocks. Internal floating piston or reservoir. Great prices and he knows all the oem valve codes, shock length and bushing sizes for the older stuff.

http://snorunner.byethost9.com

Hygear and Monster performance are good too. Though I think they cator to newer sleds more.

With the front shocks, request the big heavy duty fox bottom out bumpers. They make a big difference. You can have a more compliant ride with good bottom resistance. It's like dual rate springs. They even make dual rates better too.

Another thing that helps is getting your bars up to a more modern level and raising the seat. Grafting a fusion seat or some other higher seat is a big benefit.

I built a 2000 Indy 500xc sp with a lifted fusion seat, m10, bar risers and good front shocks. I had 3 Great seasons on that sled and liked it. So much so that my 2011 ski doo xp was a little disappointing until I got the shocks upgraded. Especially the front.

If you have any questions, just ask.



Thanks a lot for the info and I finally had some time to do some reading and I'm gonna go with a tank and seat off an 09 IQ I think I found a fair deal on eBay and I'm gonna step up to a 136 or 144" skid I see that company's sell kits to extend the tunnel and there is a Ton of info out there... happy new year..



Sent from my iPhone using Tapatalk
 
Great! Your gonna like it.
 
Rear:

If your okay with sacrificing 5 mph top speed, an m10 is still a good swap. Plus the information you need is everywhere.

Stay away from the mid to late 2000s Polaris m10s with the tubular arms. Nothing wrong with tubes per se, but these skids are not built as well and are prone to cracking.

M10 needs to be setup correctly. When it is, you get a great ride.

Or: 2002 and up Polaris "edge" skids, fusion skids, Dragon skids, even new indy skids. They are conceptually and geometrically the same. Just detail changes and trim changes thru the years.

******No matter what you choose, the shocks need to be fresh and valved correctly. Correctly as in, at least to OEM spec******

In all honesty you could swap any skid. Even an r motion. But with the edge style and m10 you are scaffolding off over 10 years of swap knowledge on the web. So it's just easier.

Front shocks:

The front of your machine thankfully has a modern level of travel and decent geometry. So you just need shocks, or your shocks serviced.

Check out this guy below...he builds and sells fox aluminum body and steel body shocks. Internal floating piston or reservoir. Great prices and he knows all the oem valve codes, shock length and bushing sizes for the older stuff.

http://snorunner.byethost9.com

Hygear and Monster performance are good too. Though I think they cator to newer sleds more.

With the front shocks, request the big heavy duty fox bottom out bumpers. They make a big difference. You can have a more compliant ride with good bottom resistance. It's like dual rate springs. They even make dual rates better too.

Another thing that helps is getting your bars up to a more modern level and raising the seat. Grafting a fusion seat or some other higher seat is a big benefit.

I built a 2000 Indy 500xc sp with a lifted fusion seat, m10, bar risers and good front shocks. I had 3 Great seasons on that sled and liked it. So much so that my 2011 ski doo xp was a little disappointing until I got the shocks upgraded. Especially the front.

If you have any questions, just ask.


I realize this is an old thread, but do you have the new link to contact SNORUNNER ?

That link above is dead

Thanks in advance
 


Back
Top Bottom